How to Vacuum a Pool?

Pool vacuuming is the best way to take away dirt and debris from your pool and ensuring its cleanliness. Simple work it may look, but it’s always worthwhile.

It will only take you a short while to effectively clean your pool getting rid of algae, hence your pool looking amazing and guaranteeing chemical balance in the pool. Want to add some vacuum routinely to your pool? It’s simple; all you need is an excellent vacuuming technique and necessary equipment.

Pool Vacuuming Essentials

Before going ahead with your pool vacuuming, ensure you have all it takes to get the work done. Here is the checklist to get you started;

1. Vacuum hose

The vacuum hose joins the vacuum head to the pool pump through the skimmer inlet to offer debris-sucking power.

2. Vacuum Plate

The vacuum plate, which is also the skimmer plate is crucial in attaching your vacuum hose to the skimmer inlet.

3. Vacuum Telescopic Pole and Head

As any swimming pool owner, the great chances are that you have a telescopic pole and interchangeable supplements like brushes, nets and skimmers. The majority of the vacuum heads are made to work hand in hand with any telescopic pole.

When choosing a vacuum head, consider your swimming pool type; for a concrete swimming pool, a wheeled vacuum head will be appropriate for stress-free movement.

How to Get Started?

Once all your vacuuming apparatus is set, it is now time to initiate your pool vacuuming. The following steps will help you vacuum the in-ground and above-ground of your swimming pool.

1. Bring together your pool vacuum

Get your vacuum head and attach it to the telescopic pole. It should snap easily, and this is a quick and straightforward task to perform.

2. Attach your vacuum hose

Fasten one end of the vacuum hose to the vacuum head and the other end to the skimmer with the vacuum plate. Remember to blow air out of your vacuum hose before connecting it to the skimmer. You can do this by holding the jet up against one pool jets until no air bubbles come out of the hose.

Filter setting to Select your filter valve setting

For swimming pools with large debris, you can set the filter valve to waste; to send the water through the drain rather than down the filter. For lighter vacuuming, let your multiport filter valve set to filter.

1. Start vacuuming

Start moving your pool vacuum in slow direct passes, the same manner you would move a vacuum on a floor. If the pool is filthy, stop on occasions to empty the pump strainer before proceeding, repeat the process severally to make sure all the dirt and debris from the pool’s floor is removed.

Keep in mind that a pool full of dirt and debris will look cloudy no matter how clean you have vacuumed it. All you need to do is leave the pool untouched after cleaning for a few hours then come back later and work on the debris, repeating the cleaning process.

In case the vacuum head gets stuck, switch it off for a few seconds to halt the vacuum force. Also, try to observe the pressure gauge of the pool filter as you go on vacuuming. In case there is a pressure rise than the recommended pressure in the manufacturer’s manual, dismiss it and backwash the filter.

2. Detach, change your filter setting and do an ultimate cleanup

After vacuuming the pool to your desire, detach the vacuum hoses and head and clean the bottom of the skimmer.  Change back your filter setting if you had changed it.

In case you are using a DE filter or sand, make sure it gets a backwash after winding up your vacuuming. For a great finish touch, fasten a brush to the telescopic pole to give the pool and its sides a great scrub.

Clean the pump strainer basket from all the debris and dirt, give your filter a last backwash if it’s a multiport system that castoff the filter setting.

If it was the waste filter setting, remember to switch the valve to filter setting and add enough water to your pool until the water level is restored. After ensuring the water level of the pool is appropriate, test it to adjust its chlorine, alkalinity and PH as needed.

How to Use a Sand Filter to clean Your Pool?

To use the sand filter as your pool vacuum cleaning method, you will need to select the right settings. It has six types of settings; recirculate, backwash, rinse, closed, waste and filter. This type of filtering is usually used for pool vacuuming as it grips minimal dirt. It is not the best filter system for pools with less dirt, and incase you have to use it; the waste setting will handle that.

After your pool is clean, it is essential to check on the manufacturer’s guide on how to backwash and clean the filter for a smooth running. The sand filter is also not the best method to clean your pool if it is loaded with algae, debris or dirt, your water level is going to decrease thus needing you to add another amount. You can use other acceptable methods to clean the pool in case of a lot of algae where a broad algae cleaning is crucial.

How to Use a Garden Hose to Vacuum your Pool?

It is another excellent way to vacuum your pool. It is an inexpensive and best alternative to clean hot tubs and smaller pools. The following are simple steps to follow;

  • Take your vacuum head and connect it to the telescopic pole.
  • Attach one end of a vacuum hose to its spigot and the other end to the telescopic pole.
  • Connect the vacuum bag to the right opening spot of the vacuum
  • Go ahead and turn off the filtering system of the pool.
  • Turn water on and merge the garden hose to the pool.
  • Steadily and slowly, move the garden hose back and forth in line along the surface to remove debris, dirt and vacuum the pool.
  • Lastly, turn on the filtration system to get rid of floating dirt and debris.

In case the garden hose loses its suction during the process, pull out the garden hose and empty its collection bag. If that doesn’t help, turn off the source of water and then turn it on again before emerging the vacuum into the water. One important thing to note is to make sure you do not try vacuuming your pool in a hurry.

You will end up stirring all the dirt and debris at the bottom surface of the pool, making it hard for the vacuum to clean. Take time and work on the entire surface of the pool to get rid of the floating debris and dirt.

Vacuuming a Pool on Backwash

It can be not very clear to clean your swimming pool as a first-time owner. Learning the best tricks on how to clean it and adequately vacuuming it is vital. The question of whether to vacuum your pool on the backwash is crucial.

Your pool can be vacuumed by backwash, but it will not be helpful as the water gets propelled backwards from end to end, thus trapping more dirt before going over the backwash hose. The dirt would get back to the pool when the pumps get back to the filter setting.

Why Shouldn’t you Vacuum your Pool on Backwash?

The reason to vacuum your pool on the backwash is when the multiport is in the backwash setting. Water gets from the pump to underneath of sand filter than the usual way of pumping at the top. The water, later on, goes up through the filter medium than to the yard pipe and finally out of the pool’s outlet. In this process, dirt trapped in the sand’s top layer gets expelled, thus cleaning the sand.

Vacuuming a pool on backwash means dirt and debris being trapped at the bottom part of the sand. This only means the dirt and debris are getting back to the pool when the multiport valve will be put back to the filter.

The other reason is that while vacuuming on backwash, the level of water in the pool reduces as the pool water gets trapped in the waste pipe. The same way the level of water in the pool will drop when a pool is dirty, and one tries to vacuum wastes.

Best Settings to Use to Vacuum a Pool

The best settings to vacuum your pool are two on the multiport valve. The settings depend on how murky the swimming pool is. The settings include;

  • Filter setting pool vacuuming

It is the frequently used setting for pool vacuuming. It is a setting used when the pool is not loaded with debris and dirt. With this setting, you get dirt trapped in the sand, thus allowing clean water back to the pool through the return jets.

  • Waste setting pool vacuuming

You will only need to use the waste setting to vacuum your swimming pool when it is foul. This is usually done after winter seasons or bad weather when the pool gets stuffed with a lot of debris and dirt.

Whatever setting you decide to use in vacuuming your swimming pool, remember that the amount of dirt is what determines your multiport filter setting. Do not let your filter reduce the amount of debris and dirt to omit from your swimming pool.

For routine vacuuming, the best setting to choose is the filter setting. It is a simple setting for ordinary pool conditions to remove pool contaminants. It is also best as it retains the level of water in the pool after filtering all the debris and dirt.

Why Invest in an Automatic Cleaner?

It is not all about having a vacuum with a fantastic filtration system is what you need. Though vital as it may seem, it minimizes the number of algae in a pool and normalizing its PH level even though not even the best filters can do all the work.

To have a sparkling clean pool, extra cleaning and vacuuming of the pool once per week is necessary. A few weeks of vacuuming and scrubbing the surface of the pool, you will come into a conclusion that an automatic pool cleaner is a significant investment worth your spending; it saves up energy and time.

Types of Automatic Pool Cleaners

As technology advances every other day, so are the invention of automatic equipment to vacuum your pools. Many people are joining the no-hand pool washing group. There are a variety of automatic pool cleaners, whatever work they do in your swimming pool, which depends on the pool’s preferences and situation.

  1. Robotic vacuum cleaner

With the robotic leaner, you do not have to attach it to the pool pump. This automatic pool cleaner is the fastest and most operative type that uses electricity. You have to connect it, plug in the switch, drop it in the swimming pool and watch it do all the hard work for you.

On the other hand, it is costly to acquire it from the market but hey, what you get is what you pay for. It is significant for large pools and hard-to-reach surfaces; the robotic vacuum cleaners are mostly operational with remote control.

  1. Pressure-side cleaner

This type of automatic pool cleaner has a collection bag, and it works by being attached to the hose of the pool filter for a pull. The only disadvantage of purchasing this type of cleaner is the replacement of bags regularly, but they reduce the wear and tear of your swimming pool by getting rid of the dirt and all its debris.

  1. Suction side cleaner

The suction side cleaner gets attached to the filter of the pool for suction. A cheaper cleaning option recommended for pools with debris and dirt troubles only.

In summary, it is necessary to vacuum your pool every week, and this is essential to keep your pool clean and retain its alkalinity. You can also vacuum your pool anytime you notice leaves, debris or dirt on the surface or by the sides of your swimming pool.

Do not forget to take note of the type of settings to handle the debris and dirt in your swimming pool. All in all, vacuuming your pool is an easy job but hard without enough knowledge to take it.



Leave a Comment